05 Identity & adulteration

How to prove Lactitol Monohydrate is what the specification says

Technical document 05 · Reviewed 2026-11-20 · Lactitol Monohydrate

On this page
  1. Why identity is a separate test
  2. The tests that answer it
  3. Common substitutions and what they look like
  4. Reading the chromatogram
  5. A practical authenticity protocol
  6. When to use a third party
  7. How this document is controlled

Identity is the first question a buyer should ask and the last one a certificate usually answers. Lactitol Monohydrate can meet its assay and still be the wrong isomer, the wrong salt, a blend, or a material from a different source. This page sets out the tests that answer the identity question and the substitutions that make it worth asking.

In one line

An assay tells you how much of the named material is present. Identity tells you that the material is the one named. Lactitol Monohydrate needs both.

Why identity is a separate test

The active is a hydrogenated sugar, so assay, moisture and the other-polyol profile belong together; the crystal form is part of the specification, not a packing detail. The assay method is chosen to measure the active. It is not necessarily chosen to distinguish the active from a close relative. That is why an identity specification names the reference standard, the chromatographic system and the secondary confirmation, not only a percentage.

The tests that answer it

  • HPLC-RI assay against a Lactitol Monohydrate reference standard
  • Other-polyol profile by the same method
  • Moisture by Karl Fischer or loss on drying, as specified
  • IR spectrum and particle-size distribution

For this grade, the primary assay is HPLC-RI. The identity evidence starts with the retention time and the reference standard, then adds the secondary test that makes the result specific. A single retention time from a single injection is weak identity evidence.

Common substitutions and what they look like

  • A different polyol blended into Lactitol Monohydrate
  • A lower-assay grade or a higher-moisture lot
  • Sucrose or dextrose used as a bulking agent without declaration
  • A coarse grade sold as a fine powder

None of these substitutions is always visible from the assay. A blend can be built to hit the same percentage. A lower-grade extract can be blended up with a carrier. The useful warning signs are a price that is far below the market, a certificate that reports only one figure, a specification that omits the other-isomer or related-substance profile, and a supplier who cannot name the reference standard.

Reading the chromatogram

Ask for the chromatogram, not only the table. The main peak should be the named material, the integration should be reproducible, and the minor peaks should match the specification. A chromatogram that shows a broad, unresolved hump where the main peak should be is a quality signal even if the integration reports 98%.

For Lactitol Monohydrate, the relevant identity format is Lactitol ≥98%, monohydrate. The certificate should report those values on the same lot, with the method and the reference standard named.

A practical authenticity protocol

  1. Match the lot number across the COA, the drum and the retained sample.
  2. Run the primary identity test against a certified reference standard.
  3. Run the secondary test that distinguishes the material from its closest substitute.
  4. Check the other-isomer, related-substance or sugar profile for the substitution the assay cannot see.
  5. Compare the result with the previous lot and with the retained sample.
  6. If the result is ambiguous, send a sample to an independent laboratory with the reference standard and the specification.

When to use a third party

Use an outside laboratory when the material is from a new source, when the price is materially below the market, when the source is unknown, or when the first shipment is critical to the project. The useful brief is narrow: test the identity questions the supplier's certificate leaves open, not a full repeat of the same panel.

Read the related pages for this grade: Lactitol Monohydrate specification and grades, COA and batch testing and identity and adulteration.

How this document is controlled

This page is part of the technical file for Lactitol Monohydrate. It is reviewed when the specification, the analytical method or the packing changes. The date at the top of the page is the review date; the current specification should be checked before a launch.

The commercial document is the specification agreed with the buyer, the batch COA for the lot and the technical data sheet supplied with that lot. If this page and the agreed specification disagree, the agreed specification governs the order. The page exists to explain the reasoning behind the specification, so a quality, procurement or technical reviewer can see why each line is there.

The product hub for this grade is Lactitol Monohydrate: specification, grades and documents. The release workflow is described on the quality and documentation page, and the analytical method behind the primary assay is listed in the method library.

Quick inquiry

Ask about this grade

Name, company, email and the question. The product and the page you are reading travel with it, so there is nothing else to select.

We use your details only to answer this inquiry. Country is detected from your connection and used only for freight and compliance. Need a written quotation instead? The full form asks for quantity, preferred form, destination market and the documents you need — those answers are what turn a reply into a priced quotation instead of another round of questions.