Which Mannitol grade fits the brief?
Mannitol is published as a family of grades, not a single drum. The grade decides the particle size, the carrier, the taste, the dissolution behaviour and sometimes the carrier system. The table below is the published starting point; the specification for the chosen grade is the document that governs release.
The grade is decided by the dosage form and the process. Mannitol is no exception: Mannitol crystal and Mannitol powder can share an assay and still behave differently in the line.
The grade map
| Grade | Best fit | What changes |
|---|---|---|
| Mannitol crystal | Chewing gum and dry blends | Standard crystalline |
| Mannitol powder | Tabletting | Finer particle |
| Spray-dried mannitol | Direct compression | Better compactibility, higher cost |
| Granular mannitol | Chewing gum | Free-flowing |
Sweetness and taste
The indicative sweetness is 50–70% of sucrose, indicative. That figure is a starting point, not a promise: sweetness depends on the matrix, the pH, the temperature, the other sweeteners and the person tasting. Mild sweetness with a cooling effect and a slightly dry mouthfeel; the tablet mouthfeel is grade-dependent.
The use level is 5–30% in tabletting and chewing gum, depending on the function. Use that range as a bench-trial window. The final level is set by the matrix, the process and the taste target.
What changes between grades
Particle size changes dissolution speed, dust and flow. A carrier changes the active content, the flow and the taste. A liquid grade adds water and a preservation requirement. A granulated grade can reduce dust and improve flow, but it may dissolve more slowly. None of these is a cosmetic difference, and none of them is captured by the assay alone.
The functional properties behind those differences are stated on the technical data sheet: Soluble in water; low hygroscopicity and a cooling effect, with good tablet compaction in the right grade. Low; easier to store than sorbitol or xylitol.
The grade decision
The level-four page for this product compares Mannitol with Sorbitol. It sets out the choice in the terms that matter at the bench: taste, solubility, process and cost per unit of sweetness.
Mannitol vs sorbitol: the tablet is the difference
Mannitol and sorbitol are stereoisomers, but mannitol is less hygroscopic and can be spray-dried for direct compression; sorbitol is more hygroscopic and used for humectancy.
How to run the trial
- Fix the target sucrose equivalence, not the powder weight. Compare grades at the same delivered sweetness.
- Test at the final pH, temperature and matrix. Water alone hides the acid and protein effects.
- Measure the sweetness at the start, the middle and the end of the shelf-life window.
- Check the physical result: clarity, colour, viscosity, crystallisation or mouthfeel as relevant.
- Record the lot number and the use level, so the result can be repeated on the next lot.
Ordering and traceability
The grade on the purchase order should match the grade in the specification and on the COA. A generic name on the order and a specific grade in the file is a documentation gap waiting for a reviewer to find it.
Read the related pages for this grade: Mannitol specification and grades, COA and batch testing and identity and adulteration.
How this document is controlled
This page is part of the technical file for Mannitol. It is reviewed when the specification, the analytical method or the packing changes. The date at the top of the page is the review date; the current specification should be checked before a launch.
The commercial document is the specification agreed with the buyer, the batch COA for the lot and the technical data sheet supplied with that lot. If this page and the agreed specification disagree, the agreed specification governs the order. The page exists to explain the reasoning behind the specification, so a quality, procurement or technical reviewer can see why each line is there.
The product hub for this grade is Mannitol: specification, grades and documents. The release workflow is described on the quality and documentation page, and the analytical method behind the primary assay is listed in the method library.
In this document
Related documents
Quick inquiry
Ask about this grade
Name, company, email and the question. The product and the page you are reading travel with it, so there is nothing else to select.